Blender Parts

Blender is one of the electrical household appliance (ARTL) are used to destroy or refine foodstuffs. This tool uses components of the four-edged blade shaped slicer. The blades are rotating through the coupling gears of rubber to the motor shaft rotates. On body weight or blender installed a switch that functions to turn on and adjust the motor. Variations of this switch is generally dependent on the brand blendernya. This switch between the different variations of the brand Philips model / type HR - 2810 / A and National blender model / type MX - T1GN. Blender National does not have the speed variation while Philips blender consists of four variations of speed according to the position of the switch to vote.
Philips Blender Model / Type HR - 2810 / A
Philips blender consists of four variations of speed according to the position of the switch voting, namely: (1) the position of the manual, (2) Neutral position, (3) position 1, and (4) position 2.
The fourth position of the switch there are differences and similarities of function, namely the manual position similar to the position 2, which is the same position where kecapatannya full speed. Sendangkan at position 1 of belender speed becomes slow. Neutral position is the position where the motor of belender no way, in other words there is no current flowing into the motor stator coil and rotot.
Components of the brand Philips blender Type HR - 2810 / A consists of: dough receptacle or material will be blended, the motor home (body), intermediate gears, motor, switch, base plate and cantilever legs. Consider Figure 82 below.

Figure 82. (a) body; (b) Components Philips Blender HR - 2810 / A.

In a blender motors there are some electronic components, such as capacitors, resistors, and diodes. These four electronic components have the following functions: 1 Capacitors serve to generate the phase difference (phase magnetic flux that is at odds with the magnetic flux generated by the primary coil). With different magnetic flux terbangkitnya that phase then the motor will rotate.
2 Resistor star serves to reduce the current to the motor to prevent overcurrent in the motor coil.
3 Diodes serves to rectify the voltage coming into the coil.
4. inductor and capacitor serves to anticipate or mengroud-high frequency affected the akibatk high rotation motors.
Specifications Philips Blender HR - 2810 / A
Item: Blender
Type: HR - 2810 / A
Manufacturer: Philips (Mexico)
Magnitude Electricity: Current, I = 1.8 amperes, working voltage, V = 220, working frequency, f = 50 Hz, Power Consumption, P = 400 Watts

Figure 83 below shows the electrical circuit blender Philips HR-2810 / A.

Electrical circuit Figure 83.-Blender Philips HR 2810 / A

Blender National Model / Type MX - T1GN
Furthermore, Figure 76, 77 and 78 at the following shows urain physical form and the components of the National-type blender × MX - T1GN, with the following specifications:
Specifications Blender National MX - T1GN
Item: Blender
Type / model: MX - T1GN
Manufacturer: National Gobel
Magnitude Electricity: Flow, I ≈ 0.82 to 0.86 amperes, working voltage V = 220-230 volts, operating frequency, f = 50-60 Hz, Power Consumption, P = 190 Watts

Figure 84. Shape Whole blender National Type MX - T1GN

Figure 84. Shape Whole blender National Type MX - T1GN.

(1) knife crusher
(2) kneading
(3) cup holder
(4) a large bowl lid
(5) the dough container (rubber coated glass bowl)
(6) body and dough bowl stand holder
(7) heat-resistant gear coupling VPC
(8) ON-OFF switch
(9) plugs
(10) coupling gear coupling between the rotor blades and the gear coupling

Figure 86.-type component in a blender National MX - T1GN

(1) lamellae commutator (2) conductor cable (from the switch to the entanglement satator) (3) brush box (4) as the rotor (5) terminal that connects the stator winding with a power source (6) cable conductors to the voltage source (7) entanglement stator (8) ON-OFF switch
National blender uses a motor to the needs suplei universal voltage of 220 volts AC at the working frequency of 50-60 Hz. 190W power dissipation. Switch that is used does not have a connection speed variation or just a single speed. Figure 87 below shows the electrical circuit blender National MX-T1 GN.

Figure 87. Blender National Electrical Circuit MX-T1 GN