Blender, like mixers, is a very basic kitchen equipment, for cutting, mixing, thickening, and liquefying food. Blender consists of a bottle (stopfles) glass or plastic on the bottom as a universal motor home, and assembled in the cutter blades stopfles, driven by a motor at the bottom. Most blenders have a problem on the blade and shaft assemblies for cutting.
Caution: Before working on the blender, make sure that the blender is not connected to the network.
demolition
Blender to work, you have to disassemble the cutter assembly and open basically to take the bike. Stopfles possible in one part, there is a cutting blade that is sealed at the bottom of the unit. To remove the seal, stopfles lift from the bottom and remove the clutch nut under stopfles. Use a cloth to protect your fingers, hold the blade in the stopfles and turn the coupling clockwise (cw) to remove it; then lift blades. If the part has not been able to move, rotate coupling clockwise (CCW) to remove it; some coupling can be removed in this way. Until you are sure coupling using twisted way in which to remove it, do not use violence at all; You will break it.
To get the motor, disconnect coupling on the top of the base (home). If the motor shaft is rotated difficult, use a screwdriver to hold the shaft and keep it out of round; swivel coupling cw to remove it. In some units, coupling rotates CCW to open it. If the clutch is composed of metal studs mounted on the bottom stopfles, insert a nail through a ventilation hole in the house / body grounding, and resist the blades of the fan with spikes to keep the shaft from rotation. Then off buttons with a wrench by turning cw or ccw.
cleaning
The fan blades and cutters are assembled in a blender should be cleaned periodically to maintain work efficiency blender. To clean the blades, remove the clutch from stopfles, and remove the blades, shaft, bracelet-cap (ring), bearing housings, and bolts that make up the cutter assembly. Arrange these parts like when you dismantle a blender, and make diagrams as you do so that you can reassemble it correctly cutter. Clean these parts in a solution of water and a little detergent RT, and dry completely. Test the cutter blades and sleepers carefully, this is the main and often broken. If these parts are damaged, replace it with a new one.
Dirt on the fan blades can cause interference. To resolve this problem, remove the bottom of the 'base' or switch plates; use a solution of water and a little detergent to clean the blade of his RT. Clean up as much on the motor so that you can reach, and also clean the body. Remove the clutch to reach the top of the 'base' to clean up the remaining parts on the motor. Be careful not to take some of the wires are wet. After cleaning, rub the parts to dry. Let the blender until completely dried before reassemble.
operation Disorders
If the blender much disturbed, most of the problems on the clutch or the fan. Coupling above is the bottom of the cutter shaft assembly; Below are the top clutch 'base' dimanastopfles coupled to the motor. If another clutch looks worn, replace with a new one that is similar; attach a new clutch as the clutch pairs long.
Disorders exceptional or very conspicuous usually caused by a fan blade is bent or broken. To resolve this problem, open the 'base' on the unit and check and clean the fan blades. If the blades slightly bent, make straight with pliers; if you can not straighten it, replace the blades of the fan assembly. To remove the blades of the fan assembly, remove the nuts that hold the booster motor shaft; or, if the blade assembly is very shifted, pull out. Replace blades assembly with a new one that is similar; attach the new assembly in the same way as in the old assembly.
The disorder can also be caused by the loss or destruction of the blades of the cutter. Test assemblies blades. If the blades loose, tighten it; if the blades were destroyed, remove it, as detailed above, and replace it with new blades are similar.
leakage
Leaks are usually caused by damage to the stopfles or seal for the pressure at the bottom of the blender stopfles. If stopfles damaged, replace it with a new one that is similar. Stopfles plastic blender occasionally may develop that could lead to leaks; such meeting for the type of small cracks. If the cracks are the source of the leak, replace stopfles.
If there are cracks that are not visible on stopfles, this problem may be possible to seal the pressure. Lift the cutter assembly, as detailed above, and test the seal. If the seals wear out, break, or hard, replace it with a new one that is similar.
Leakage circular on stopfles blender cover is usually caused by a worn cover gasket. If this is the case, the best is to replace the cover, buy a new cover similar.
switches
Motor is controlled by a switch with many positions, the base of the unit. If the blender has a double switch and / or button press, or a switch that is controlled by the rectifier at each position of the speed, do not try to handle it yourself, take it to a professional service aircraft.
Single speed switch can be replaced if it does not work. If the blender can not spin, and he has received the power, the switch may be damaged. Open the base unit on the top or bottom or switch plate, as above, and Test it switches to the AVO, setlah on RX1 scale; meter will point zero. If the switch is damaged, replace it with a new one that is similar. Remove the captive screws to take the old switch from its place; setlah new switch in the same position, connect in the same way as the old switch connections, and replace the screws.
timer
Some blenders have a timer, the timer controller placed on the control panel. If the timer does not work, replace with a new one similar, do not try to fix it. Timer timer control buttons are next; to reach it, remove the key. If the staring at the timer shaft, pulling them out; if it is held in place by a pair of screws, remove the screws to take the keys. Then remove the cover plate covering it. If there is a lot of wire connections to the timer, and it is used to control some settings, do not try to change the self-timer; take it to a professional service. If the timer is a simple unit, however, you have to replace it. Remove it from its place, and mark the cable connection so you can replace it with either the new timer. Set a new timer in place, connect the cable, and attach a timer in place the same way as the old timers on the connection.
Motor
If the switch has been replaced and the motor has not spinning, or if it spins but not stabilized, problems arise, smells, or sprinkling arise, it is possible the motor brush wear charcoal. Replace it with a new charcoal similar brush. If the motor does not spin up, or if there is some serious motor problems, as well as the release of the armature windings or hubungsingkat, take a blender to a professional service.
TROUBLE SHOOTING
PROBLEM
|
POSSIBLE CAUSE |
SOLUTION
|
| Blender does not rotate | 1 No power 2 Errors switch 3 Brush wear charcoal 4. electrical system short circuit 5. motor impairment |
1 Check the power cord, plug, and KK. Check-safety lawyer melting or CB on the main panel; correct sequence. 2 Replace the switch; or take it to a professional service 3 Check the brush; If worn, replace 4 Bring to a professional service 5. Bring to a professional service |
| Blender voltage, vibrating | 1 The power cable is damaged. Electrical system hu- short man | 1 Test cable; replace if damaged. Bring to a professional service |
| Motor arise sparks | 1 Brush wear charcoal. 2. Motor damaged | 1 Check the brush; If worn, replace it. 2. Bring to a professional service. |
| Motor rotates slowly | 1. Stopfles blender too much load 2. charcoal brush wear | 1 Reduce the load, or add a little liquid into stopfles 2 Check the brush; If worn, replace. . |
| Motor rotates, but the blades are not spinning | 1 Stopfles not place the well-worn or dirty 2 Clutch 3 Assembled cutter dirty 4 Blade cutting crooked or worn |
1 Sit stopfles so clutch in stop-fles right with the clutch on the base 2 Check coupling; if dirty or worn, replace 3 Clean the cutter assembly 4 Replace the cutter blade |
| Disruption of work (operations) | 1.-rainbow terha cutter blades 2 cutting blades bent or worn 3 Blade fan bent 4. Clutch wear 5. Motor damaged |
1 Lift the barrier of pemotong2. Check coupling; if dirty or worn, replace 3 Align the blade, or replace the fan blade assembly 4 Check the upper and lower coupling, if worn replace 5. Take it to a professional service. |
