In general person as stated in the blender that everything is taken care of by the patient will be durable. This opinion applies also to the use of Electric Appliances. Electric Appliances are in use constantly cared for will last. Even so, sometimes the damage can not be avoided. Therefore, in addition to understand the treatment, it is also necessary to master properly repair the damage an Electric Appliances, especially for those who follow this course. Types of maintenance and repair Electric Appliances which will be discussed at this point is the maintenance and improvement of a blender in general.
1 Treatment Blender
The steps that need to be done in treating a blender so durable as well as their use of the book or brochure use. Read a book or brochure carefully the instructions for use before using the blender. Books or brochures usage instructions included in the package blender blender when you first buy a blender. Check the existence of a book or brochure these instructions when you buy a blender. If no, mita on the seller. Do not buy a blender that is not accompanied by a book or brochure instructions.
Work on all orders that are required in a book or brochure that when you use a blender, and avoid all that you are doing is forbidden. In general, book or leaflet containing the instructions for use of the use of steps as follows: 1 Check and match the needs of the working voltage and frequency suplei with attached voltage and operating frequency in which you would use a blender.
2 Position the blender switch at position "0" or off.
3 Insert or attach the proper batter bowl used above stand holder until the second coupling gear - gear coupling and gear coupling rotor- knife properly established. Remember !!! Cover the bowl of dough with the meeting. If using a large bowl that is destined for the manufacture of juce, then do not forget to install the extended stalk stirrer available in through hole on the lid of the bowl.
4 Insert the 'plug' it right on the outlet voltage AC 220 ~ 230 volts, 50 ~ 60 Hz. Attention! This magnitude should not be violated. Violation of these electrical quantities can cause fatal damage to the blender. Hold both ends of the plug (not the cable conductor) when inserting and removing plugs to and from the socket.
5. While still holding the bowl of dough, place the ON-OFF switch in the 'ON' position.
6 Look carefully blended dough conditions. If the circulation has been sounded smooth dough, then stop by the road round belender restore the position of the switch in the OFF position. Do not pull the bowl of dough in the state of the motor is still rotating blender. Dangerous!
7 Attention! Never too old to run the motor blender, to over an hour without stopping. The use of well above an hour without stopping will increase the temperature of the motor and the heat would be fatal. These conditions may result in a blender motors burned.
8 Wipe or wash clean all components of the blender except the body shortly after use so as not moldy.
9 Attention! Blender body should not be washed. In the body there is a blender blender motors and electrical circuits. Wash the blender body will moisten blender motors and electrical circuits. This can result in a blender motors and electrical circuits connected blender briefly (shorted). Subsequent impact is a series of electrical motors and the motor will burn when run again.
2 Blender Repair
In urain previously been described that damage to the Electric Appliance sometimes unavoidable. Damage may occur due to: 1 factor of age or frequency of use of a blender 2 disaster factors, such as natural disasters and accidents to carelessness or error factor 3 users.
The age factor or the frequency of use of a blender and difficult to avoid disaster factor but carelessness or error factors can be avoided by increasing knowledge about belnder and how to use them. Therefore, the knowledge and skills to repair the damage needs to be owned, especially by those who follow this course. Here are some types of damage diurakan blender and repair steps.
a) The blender motor does not rotate
Blender Motor does not rotate because there is no electrical current that goes into the motor blender. This condition is caused by damage to the parts through which the electric current to the coils or windings in the motor, such as: plugs, wires introduction, contact or selector switch liaison rounds, brushes, commutator, and the motor coil.
Corrective measures that need to be done, namely: 1 Check the physical condition of the plug with the naked eye observations of possibilities: burns, broken or separated from contact with the cable ties introduction. Then, if it looks good physical condition, proceed with the examination of the relationship contact with the terminal end of the cable that is connected to her introduction to the use of a multimeter (ohms position, scale 10X). If the needle moves to the right towards the multimeter to measure point '0' and pointed to some basic values, such as 0 ohms or close to 0 ohms and not move from that value, then plug the blender is still good. In addition to these conditions, the plug is damaged and must be replaced with a new one;
2 Check the connection and condition of the cable conductors, do not let anyone apart. Then use a multimeter (position select switch on poisisi 'ohm', scale 10X) to check the condition of the cable should not be dropped out of the 'inside'. Disconnect 'in' means a wire conductor inside the insulation sheath conductor 'broken' or disconnected, so the break point or position not reachable through the eyes of the senses, so the condition should be detected with a multimeter or ohm meter;
3 Check the condition of the brush (left-right), do not get broken, worn out or compressed spring apart so that contact is lost between the commutator-brush-stator winding-switch-cable-conductor plugs. Brush is broken, too worn or missing compressed spring can cause loss of contact relation between entanglement 'rotor and' stator 'motor blender. As a result, the motor can not tersuplei blender electric current and does not rotate. If the brush in a broken condition, too worn or lost spring press, the brush should be replaced with a new one.
4 Check the condition of the commutator lamellae. Do not let the tip of the rotor windings lost contact with the commutator lamellae, or rotor windings have been burned. If the apparent end of the rotor windings are disconnected from the lamellae commutator or rotor windings have been burned, then the motor will not spin blender.
5 Check the condition of the stator winding connections (left-right) using the ohm meter (multimeter) not to burn or cut off. If burned or broken, then the motor will not spin blender.
b) blender motor does not rotate, but the buzzing
Conditions or damage that causes the motor is not rotating blender, but buzzing the auxiliary field windings or rotating field or main field of the stator there are short circuited. Similarly, if there is a blender motor rotor windings are short circuited. Short circuit in the motor stator windings or rotor blender blender cause the motor to lose torque, while the electric current flowing. As a result, the motor buzzing until it vibrates. If this condition is allowed to continue about 10-30 minutes, then the stator windings and the rotor can burn. Repair steps are: Replace coil or auxiliary motor stator main coil, or replace the motor rotor coil blender. Replacement stator windings can be done alone or entrusted to a handyman service. If pengantiannya done alone then there are some practical things you can do, namely: 1 Look carefully and note the size of the wire used email each type of entanglement,
2 Notice and images with precise direction of rotation of turns of each winding (auxiliary field winding, main field windings and rotor windings). Read books that specifically discusses how to roll winding (coil) electric motor, length or number of turns in each coil need not questioned, but simply you weigh carefully the weight of the wire required email each type of coil,
3 when you roll it is recommended you use a soft glove and made of cloth 'Cotton', so that the possibility of blisters wire insulation due to the influence of contamination email directly with your hands that may be damp or wet, or damaged due to scratching your nails can be avoided. Then, do not pull the wire rub it while doing email while rolling, because the wire insulation can chafe email.
c) Motor blender rotates, but issued a spark.
This damage occurs because of the relationship between the brush and commutator contact uneven or less fit. Repair steps are:
1 Check the motor brushes, do not let the brush has no right to close or connect the brush contact with commutator lamellae well; and
2 Check the condition of brushes, replace if it is too short so that the concave surface is no longer covered or connect the relationship between the lamellae-lamellae brushes rotor commutator.
d) Motor blender rotates, but it vibrates
Conditions rotating blender, but shaking can be caused by some damage done to the motor mechanical systems, such as: 1 brush motor used is too hard (the density is not in accordance with the original brush density)
2 commutator surface lamellae-lamellae in the cycle is not flat, so the brush jump-lamellae had anything against uneven when the rotor rotates
3 stalks Teeth coupling between the stirrer and rotor wear enough or there are some missing or broken teeth
Round 4 axles (shaft) of the rotor is no longer centered. This condition is generally caused by keruskan bearing (lava) mounting the rotor (front and rear), or the bearing holder has been shifted due to the influence of excessive heat during use.
Corrective measures that need to be done on the damage terasebut conditions, namely: 1 Replace brush for damage first, use original
2 Replace the rotor, because the second keruskan very hard to do this repair. Require special equipment to do so. And may be the price to which particular equipment is more expensive than the price of the rotor
3 In the third keruskan, a tooth with a new coupling
4 Meanwhile, the damage is very difficult fourth diperbaili, except replace the bearings, rotor, and the rotor holder. In general, the holder of the rotor is not sold separately, even directly connected with the body blender. So its replacement requires another blender body or a new body if there is a sale.
e) Motor blender rotates, but when the conductor of the cable actuated or the motor does not move sometimes moving or rotating
Rotating blender motor condition, but when the cable is moved or moving pengtarnya sometimes not spin the motor can be caused by: a. damage to the brush system b. dropped out of the cable conductors.
Repair steps are: a. Check the brush system, there may be one of those brushes that off spring compressed. Fix! Should be replaced with a new one. Remember do not replace brush or just one side only, it affects the equilibrium pressure of the brush against the commutator motors
b. Replace the cable with a new conductor. In general, the conductor wires are available and sold separately. Persetnya price of Rp 3,500 in 2004.
f) Motor blender rotates, but issued a harsh sound
Blender Motor rotates, but issued a harsh sound is generally caused by damage to the rotor bearing axles. There are one or more of the bullets that are too worn out bearing against the bearing or the circle is broken. This damage gives opportunities rotor having a circle jerk or lentingan against the bearings when the motor rotates to remove coarse rattling sound.
g) Motor blender rotates, but no dough mixer rotates
Blender Motor rotates, but no dough mixer spins can be ascertained that the damage occurs in the coupling tooth grasping function stalk stirrer and connected to the rotor rotary gear is worn. The only countermeasures against this damage is replace it with a new coupling gear.
No comments:
Post a Comment